Basic EPON OLT CLI Configure | CDATA | ECOM

-

 

LOGIN Procedure:
Cofigure the OLT device you'll need to access the device properly. There are several methods to login OLT device like Use console port, MGMT Port, Type-C Port (if available). And access remotely within same network.


Console Port:

N.B.Maintain Console cable with Console Converter


Step 1: Use DB9 USB converter for Console
Step 2: Connect with OLT Console port to PC USB
Step 3: Download and install terminal software for gain access
Step 4: Find the COM port no and use 9600 data rate for EPON

-----------------------------------------------------------------------------------------------------------------



MGMT Port:

N.B.Any UPT cable can be use fot local access of OLT


Step 1: Connect UTP cable with OLT MGMT to PC LAN
Step 2: Set same series of OLT IP on the PC Network Adapter
Step 3: Browse with the OLT IP into PC browser
-----------------------------------------------------------------------------------------------------------------

VLAN Configure




VLAN Create

N.B.Create One or Multiple VLAN at a time

ECOM-EPON-OLT(config)# vlan 46
ECOM-EPON-OLT(config)# vlan 47,48
ECOM-EPON-OLT(config)# vlan 50-100
ECOM-EPON-OLT(config)# vlan 11-13,26,28,30-45
-----------------------------------------------------------------------------------------------------------------

VLAN Delete

N.B.Delete One or Multiple VLAN at a time

ECOM-EPON-OLT(config)# no vlan 46
ECOM-EPON-OLT(config)# no vlan 47,48
ECOM-EPON-OLT(config)# no vlan 50-100
ECOM-EPON-OLT(config)# no vlan 11-13,26,28,30-45
-----------------------------------------------------------------------------------------------------------------

PON VLAN Assign

N.B.Assign VLAN on PON Ports

ECOM(config)#
ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)#vlan mode 1 access
ECOM(config-interface-epon-0/0)#vlan native-vlan 1 11
ECOM(config)#
ECOM(config-interface-epon-0/0)#vlan mode 2 trunk
ECOM(config-interface-epon-0/0)#vlan trunk 2 22,24-28
ECOM(config)#
ECOM(config-interface-epon-0/0)#vlan mode 3 hybrid
ECOM(config-interface-epon-0/0)#vlan hybrid 3 tagged 33
ECOM(config-interface-epon-0/0)#vlan hybrid 3 untagged 34
ECOM(config-interface-epon-0/0)#vlan native-vlan 3 35
ECOM(config-interface-epon-0/0)# exit
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

ONU VLAN

N.B.VLAN tagging (one or many) on specific ONU

#01 Tag Single VLAN on specific ONU

ECOM(config)#
ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)# ont port native-vlan 1 1 eth 1 vlan 46
ECOM(config-interface-epon-0/0)# exit
ECOM(config)#

#02 Tag Multiple VLAN on specific ONU

ECOM(config)#
ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)# ont port vlan 1 1 eth 1 translation 110 user-vlan 110
ECOM(config-interface-epon-0/0)# ont port vlan 1 1 eth 1 translation 111 user-vlan 111
ECOM(config-interface-epon-0/0)# ont port vlan 1 1 eth 1 translation 112 user-vlan 112
ECOM(config-interface-epon-0/0)# ont port vlan 1 1 eth 1 translation 113 user-vlan 113
ECOM(config-interface-epon-0/0)# exit
-----------------------------------------------------------------------------------------------------------------

N.B.UP-Link VLAN Assign on GE(1G) or XGE(10G) Ports

ECOM(config)#
ECOM(config)#interface ge 0/0
ECOM(config-interface-ge-0/0)#vlan mode 1 access
ECOM(config-interface-ge-0/0)#vlan native-vlan 1 11
ECOM(config)#
ECOM(config-interface-ge-0/0)#vlan mode 2 trunk
ECOM(config-interface-ge-0/0)#vlan trunk 2 22-24,28
ECOM(config)#
ECOM(config-interface-ge-0/0)#vlan mode 3 hybrid
ECOM(config-interface-ge-0/0)#vlan hybrid 3 tagged 33-35
ECOM(config-interface-ge-0/0)#vlan hybrid 3 untagged 36-38
ECOM(config-interface-ge-0/0)#vlan native-vlan 3 39
ECOM(config-interface-ge-0/0)#exit
-----------------------------------------------------------------------------------------------------------------

LACP VLAN Assign

N.B.Assign VLAN on Link Aggregation Control Protocol (LACP) Port

ECOM(config)#
ECOM(config)#interface ge 0/0
ECOM(config-interface-ge-0/0)#vlan mode 1 access
ECOM(config-interface-ge-0/0)#vlan native-vlan 1 11
ECOM(config)#
ECOM(config-interface-ge-0/0)#vlan mode 2 trunk
ECOM(config-interface-ge-0/0)#vlan trunk 2 22-24,28
ECOM(config)#
ECOM(config-interface-ge-0/0)#vlan mode 3 hybrid
ECOM(config-interface-ge-0/0)#vlan hybrid 3 tagged 33-35
ECOM(config-interface-ge-0/0)#vlan hybrid 3 untagged 36-38
ECOM(config-interface-ge-0/0)#vlan native-vlan 3 39
ECOM(config-interface-ge-0/0)#exit
-----------------------------------------------------------------------------------------------------------------

PORT Configure



PON Mode change

N.B.Change PON Port mode into access/trunk/hybrid mode.
-Access mode allows single VLAN only
-Trunk mode allows Multiple VLAN
-Hybrid mode is the combination of Access and Trunk Both


ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)# vlan mode 1 access
ECOM(config-interface-epon-0/0)# vlan mode 2 trunk
ECOM(config-interface-epon-0/0)# vlan mode 3 hybrid
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

GE Mode change

N.B.Configure GE (1G) UP-link port mode


ECOM(config)# interface ge 0/0
ECOM(config-interface-ge-0/0)#vlan mode 1 access
ECOM(config-interface-ge-0/0)# vlan mode 2 trunk
ECOM(config-interface-ge-0/0)#vlan mode 3 hybrid
-----------------------------------------------------------------------------------------------------------------

XGE Mode change

N.B.Configure XGE (10G) UP-Link port mode

ECOM(config)# interface xge 0/0
ECOM(config-interface-xge-0/0)#vlan mode 1 access
ECOM(config-interface-xge-0/0)# vlan mode 2 trunk
ECOM(config-interface-xge-0/0)# vlan mode 3 hybrid
-----------------------------------------------------------------------------------------------------------------

LACP Mode change

N.B.Configure LACP port mode

ECOM-EPON-OLT(config)# DEMO
-----------------------------------------------------------------------------------------------------------------

Remote Management IP Configure



Assign IP

Step-#01 Configure the valid IP
N.B.Configure the remote access Management IP on Default VLAN 1 with valid subnet mask

EPON-OLT(config)#
EPON-OLT(config)# interface vlanif 1
EPON-OLT(config-interface-vlanif-1)# ip address 192.168.89.22 255.255.255.0
EPON-OLT(config-interface-vlanif-1)# exit
EPON-OLT(config)#

Step-#02 Route The IP
N.B.Route the remote access Management IP properly. Otherwise it'll not reachable. Then ping this OLT IP (192.168.89.22) from your MAIN ROUTER.

EPON-OLT(config)#
EPON-OLT(config)# ip route 0.0.0.0/0 192.168.89.1
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------

Assign IP on VLAN

N.B.Configure GE (1G) UP-link port mode

EPON-OLT(config)#
EPON-OLT(config)# interface vlanif 46
EPON-OLT(config-interface-vlanif-46)# ip address 192.168.89.22 255.255.255.0
EPON-OLT(config-interface-vlanif-46)# exit
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------

MGMT IP Change

N.B. Its better to change your MGMT Port IP to prevent unwanted access. But make sure you won't forgot the IP.

EPON-OLT(config)#
EPON-OLT(config)# interface mgmt
EPON-OLT(config-interface-mgmt)# ip address 192.168.1.100 255.255.255.0
EPON-OLT(config-interface-mgmt)# exit
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------

Configure LOOP Protection



Global Loop

N.B.Activate Global LOOP Protection for whole OLT. For this configuration, If LOOP raised then whole OLT will down


ECOM(config)#
ECOM(config)# loopback-detection enable
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

PON Port Loop

N.B.Activate LOOP Protection on every PON Port individually.. For this configuration, If LOOP raised into any PON. Then that will down


ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)# loopback-detection 1-8 enable
ECOM(config-interface-epon-0/0)# exit
-----------------------------------------------------------------------------------------------------------------

N.B.Activate LOOP Protection on the GE (1G) and XGE (10G). For this configuration, If LOOP raised then that UP-Link will down


ECOM(config)#
ECOM(config)# interface ge 0/0
ECOM(config-interface-ge-0/0)# loopback-detection 1-8 enable
ECOM(config-interface-ge-0/0)# exit
ECOM(config)#
ECOM(config)# interface xge 0/0
ECOM(config-interface-xge-0/0)# loopback-detection 1-2 enable
ECOM(config-interface-xge-0/0)#exit
-----------------------------------------------------------------------------------------------------------------

ONU Loop

N.B.Activate LOOP protection on all ONU. Remember, Every time new ONU register you have to run this command everytime for that newly registered ONU


ECOM(config)#
ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)# ont ring check 1 all enable
ECOM(config-interface-epon-0/0)# ont ring check 2 all enable
ECOM(config-interface-epon-0/0)# ont ring check 3 all enable
ECOM(config-interface-epon-0/0)# exit
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

ONU Blacklist

N.B. Whenever LOOP raise try to clear the loop physically. If not possible block the ONU


Step 1: Add the ONU to Blacklist

ECOM(config)#
ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)# ont black-list add 4 00:00:00:00:00:00
ECOM(config-interface-epon-0/0)# exit
ECOM(config)#

Step 2: Delete the ONU from Blacklist

ECOM(config)#
ECOM(config)# interface epon 0/0
ECOM(config-interface-epon-0/0)# ont black-list del 4 00:00:00:00:00:00
ECOM(config-interface-epon-0/0)# exit
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

Check Minor Information



ONU Info

N.B. With this command you will find how many ONU has been registered into a specific PON port. Also, with this CLI command you can check How many ONU online and how many ONU are offline

EPON-OLT(config)#
EPON-OLT(config)# show ont info 0/0 1 all
EPON-OLT(config)# show ont info 0/0 2 all
EPON-OLT(config)# show ont info 0/0 3 all
EPON-OLT(config)# show ont info 0/0 4 all


N.B.With this command you can check UP Time, Model, Approximate distance and Type of ONU

EPON-OLT(config)#
EPON-OLT(config)# show ont basic-info 0/0 1 all
EPON-OLT(config)# show ont basic-info 0/0 2 all
EPON-OLT(config)# show ont basic-info 0/0 3 all
EPON-OLT(config)# show ont basic-info 0/0 4 all
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------

ONU Optical Tx/Rx Info

N.B.Here you can find ONU Rx, Tx, Bias current, Voltage and Temperature

EPON-OLT(config)#
EPON-OLT(config)# interface epon 0/0
EPON-OLT(config-interface-epon-0/0)# show ont optical-info 1 all
EPON-OLT(config-interface-epon-0/0)# show ont optical-info 2 all
EPON-OLT(config-interface-epon-0/0)# show ont optical-info 3 all
EPON-OLT(config-interface-epon-0/0)# show ont optical-info 4 all
EPON-OLT(config-interface-epon-0/0)# exit
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------

Delete only all offline ONU

N.B.With this command all Offile ONU will delete at a time

EPON-OLT(config)#
EPON-OLT(config)# interface epon 0/0
EPON-OLT(config-interface-epon-0/0)# ont delete offline-list 1 all
EPON-OLT(config-interface-epon-0/0)# ont delete offline-list 2 all
EPON-OLT(config-interface-epon-0/0)# ont delete offline-list 3 all
EPON-OLT(config-interface-epon-0/0)# ont delete offline-list 4 all
EPON-OLT(config-interface-epon-0/0)# exit
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------

Delete all ONU (Online/Offline)

N.B.With this command all (Offile + Online) ONU will delete at a time

EPON-OLT(config)#
EPON-OLT(config)# interface epon 0/0
EPON-OLT(config-interface-epon-0/0)# ont delete 1 all
EPON-OLT(config-interface-epon-0/0)# y
EPON-OLT(config-interface-epon-0/0)# ont delete 1 all
EPON-OLT(config-interface-epon-0/0)# y
EPON-OLT(config-interface-epon-0/0)# ont delete 3 all
EPON-OLT(config-interface-epon-0/0)# y
EPON-OLT(config-interface-epon-0/0)# ont delete 4 all
EPON-OLT(config-interface-epon-0/0)# y
EPON-OLT(config-interface-epon-0/0)# exit
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------

ONU User MAC

N.B.Here you'll find the end user MAC address. It means The user who connected with ONU LAN, It's MAC address will show with this command. The MAC address could be any device like OLT, ONU, Switch, Server, PC, Router any L2/L3 devices


EPON-OLT(config)#
EPON-OLT(config)# show mac-address ont 0/0/1 18
EPON-OLT(config)#
-----------------------------------------------------------------------------------------------------------------Check Other important Info




Check FAN

N.B.DEMO


ECOM(config)#
ECOM(config)# show fan
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

Check CPU

N.B.DEMO


ECOM(config)#
ECOM(config)# show cpu
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

Check RAM

N.B.DEMO


ECOM(config)#
ECOM(config)# show memory
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

Check Temperature

N.B.DEMO


ECOM(config)#
ECOM(config)# show temperature
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

Check UPTIME

N.B.DEMO


ECOM(config)#
ECOM(config)# show uptime
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

Check Power Supply

N.B.DEMO


ECOM(config)#
ECOM(config)# show power state
ECOM(config)#
-----------------------------------------------------------------------------------------------------------------

Comments

Post a Comment